Skip to contentFarm Fresh
to Market
Discuss a Labs project
Menu

Forem Labs / INVENTIONS & PROTOTYPES

Our ideas.
Made visible.

Our work reaches across the operation: crop establishment, coordinated climate, vine care, harvesting, packaging, storage, materials and energy. Explore each application and its equipment. The Forem Greenhouse Harvester combines aisle travel and vertical positioning with crop-specific tools; the connected software makes the wider system inspectable and easier to plan.

FROM A NEED TO A TESTABLE DESIGN

Forem Labs develops the assembly concepts shown here using individually sourced components. The interactive models and planning tools are available to explore. Hardware configurations remain development work; supplier components retain their own identities and sources.

01 / Forem Labs equipment

Forem Greenhouse
Harvester

Michael Forem’s harvester design uses one rolling platform for tomatoes and peppers. See the tool pick a single fruit, then watch the padded catch basket retract and tip into the main case.

Forem Labs / ROLL · LIFT · APPROACH

One cup. One grape tomato.
ONE SHARED PICKING HEAD
LOADING INTERACTIVE 3D

Forem Greenhouse Harvester · positioning model

Optional: gently part the canopy

Two soft guides beside the picking head could extend into the foliage, part leaves and retract. This is a motion illustration; force limits, snag response and plant damage need testing.

Move the picking head & inspect dimensions

WORKING ENVELOPE / METRES

Roll along the aisle.
Lift the whole tool carriage.

All dimensions are design assumptions for the greenhouse model. The controls move connected geometry; they do not operate equipment or establish load capacity.

Manual controls show roll, lift and approach. Use the picking cycle to follow the fruit into the catch basket and main case.

Grid spacing: 250 mm

TOOL HEAD / CLOSE APPROACH

Move the picking head 20 mm at a time.

The approach motor turns the screw. Its moving nut slides the deck and the single suction cup toward the crop. The camera stays on the lift carriage. The echo sensor moves with the tip to check the remaining gap.

Open the close-up, then advance three times to see the tool head move toward the same fruit. The camera view holds steady so you can see the gap close.

Aisle travel is held while the carriage is raised or the tools extend. This is a preview interlock, not a validated machine safeguard.

Overall running footprint
820 × 1,050 mm
Fixed mast height
2,600 mm
Current suction-cup height
1.49 m
Modelled bed-edge aisle
2.10 m
Lane centre toward near bed
+200 mm
Near wheel to bed edge
440 mm
All stowed hardware to near bed
Loading geometry

The full-hardware gap is smaller than the wheel gap. Both are model geometry only; foliage, crop movement, floor variation and safe operating clearance are unverified.

What these dimensions mean

The existing model places 900 mm beds at centres −1.50 m and +1.50 m, leaving a 2.10 m bed-edge aisle. The nearest planted line is at +1.20 m. The drawn paving is wider than that clear aisle and is not used as the clearance measurement. The pepper assembly adds a supported 90 mm adapter so its wire reaches that line at full approach; actual stems, foliage and obstacles need a survey.

The carriage value is its mounting datum. Tool heights are calculated separately from the mounted geometry. The base is deliberately held during lifting and crop approach; stability, payload, braking, floor slope remain engineering work. The picking cycle illustrates the proposed basket transfer and release.

  • Mast section and base ballast/load capacity
  • Guide rail series, bearing trucks and screw pitch/diameter
  • Lift actuator torque/speed, brake holding capacity and stop architecture
  • Approach actuator and stiffness
  • Cable-carrier bend radius and ratings
  • Crop payload, dynamic stability and allowable floor slope

THE PICKING CONCEPT

Approach. Hold. Transfer.

One compliant suction cup supports one tomato. The camera locates the visible fruit and stem, and the proposed acoustic sensor helps with the final approach. The guarded wire separates the supported fruit in the illustrated cycle. Cup fit, hold confirmation and cut quality need crop trials.

What this view establishes

The mast, carriage, guides and tool mounts define a connected mechanical envelope. Dimensions here are authored assumptions. Selected component drawings, load analysis and physical trials must establish compatibility and performance.

Every component & its purpose
  1. 01

    Locate and approach one fruit

    One regular RGB camera is intended to identify a reachable ripe grape tomato. The fixed crop illustration includes neighboring green fruit. The lift and approach slide position the single-cup carrier; a proposed tip echo sensor assists the last part of the approach.

  2. 02

    Hold, then separate the stem

    One soft cup supports the selected fruit. The latest shared head adds a guarded heated-wire span at the stem. Contact, cut quality and damage limits require crop trials.

  3. 03

    Catch, retract and empty the load

    The cup releases the picked fruit into the small padded basket while neighboring fruit stays on the vine. The example load reaches its full point, then the proposed guide and gate carry and empty the catch basket into the fixed main case.

The earlier static render is superseded by this dimensioned lift study. Selected supplier dimensions must replace assumed component envelopes before fabrication. No payload, stability, picking rate or labor saving has been established.

THE WHOLE OPERATION / EQUIPMENT + SOFTWARE

The machine is one part.
The system is the whole idea.

Move through every application, from the first seed to the delivered product. Open the existing assemblies, inspect their parts and connect them to the tools that plan the work.

01 / NURSERY / FLOOR / BEDS / WATER

Establish the crop

Build from the ground up: prepare the surface, support the bed, contain the growing medium and deliver water to the roots.

  1. Prepare subgrade, drainage and ground separation.
  2. Fit the bed supports, liner or growing bags and collection path.
  3. Sow identified trays; establish plants and connect drip lines.
Assembly scope and next engineering detail

The growing model contains individual plant positions. Floor layers, bed liners and greenhouse films are separate parts; alternatives are not automatically added together as one installed bill.

02 / SHADE / ROOF / MIST / AIR / SENSING

Coordinate the climate

Share a growing target across houses, then use local measurements to decide how each shade, vent, fan and mist line responds.

  1. Measure crop light, air temperature, humidity and crop stage.
  2. Choose a reference house using observations and quality records.
  3. Share matching-stage targets; adjust each house locally.
Assembly scope and next engineering detail

A shade drive uses its own motor, pulling line, guides, end stops and power module. The cord moving the shade is distinct from the heated wire used for pepper cutting.

03 / CROP HOOK / TWINE / CLIP / TRELLIS

Lower and care for the vine

Keep the crop supported as it grows, then lower and move the trained vine without making the fruit or stem carry the working load.

  1. Inspect the hook, overhead wire, twine and stem clips.
  2. Support the vine while paying out a controlled length of twine.
  3. Move the vine along its row and secure the next position.
Assembly scope and next engineering detail

The lower-and-lean hook is inspectable now. A motorized lowering mechanism still needs a defined load path, grip, payout limit and supervised failure test; the existing component is not presented as an already automated machine.

04 / MOBILE BASE / LIFT / CROP-SPECIFIC TOOLS

Move. Lift. Reach. Harvest.

Roll along the working aisle, raise the tool carriage, reach the crop and bring the separated fruit into a receiving container.

  1. Travel with the tool retracted and the carriage lowered.
  2. Stop the base, position the carriage and approach the crop.
  3. Support the fruit with the cup, separate the stem, then collect the fruit in the moving catch basket. A full basket retracts and tips into the main case.
Assembly scope and next engineering detail

The current workshop links the whole-machine envelope, travel controls, individual assemblies and build budget. One supported suction cup, one camera, one acoustic tip sensor and a guarded heated wire serve both crop views. Optional retractable soft guides could part leaves without adding picking arms.

05 / GENTLE HANDLING / WEIGHING / PACK / LABEL

Inspect and pack the harvest

Turn picked fruit into an identified buyer pack, keeping handling, inspection, weighing and the packaging itself visible.

  1. Receive shallow containers and preserve the harvest-lot identity.
  2. Inspect the fruit and separate unsuitable product.
  3. Check pack weight, close the chosen container and attach the lot label.
Assembly scope and next engineering detail

Explore the retail pack, carton, lid, divider, label and check scale as separate pieces. Commercial inspection and grading equipment keeps its supplier identity; a custom Forem grading mechanism is not implied.

06 / CARTON / PALLET / FILM / HANDOFF

Wrap and release the load

Collect the finished packs into a stable dispatch unit, apply suitable restraint and keep the shipment linked to its records.

  1. Arrange cartons for load support and the required ventilation.
  2. Select the pallet and stretch-film restraint for the actual load.
  3. Check identity, release conditions and receiving requirements.
Assembly scope and next engineering detail

The pallet, restraint film and cartons have their own 3D assembly. A powered wrapping station needs a specified film path, moving axis, guarded area and load-restraint trial before its cycle can be engineered.

07 / STORAGE / OBSERVATION / TRANSPORT

Know what is ready to move

Connect storage conditions, product identity and the delivery requirement so the next person receives a clear handoff.

  1. Record the lot, location, quantity and storage requirement.
  2. Review door and temperature observations with an accountable operator.
  3. Release the load to a defined destination and receiving window.
Assembly scope and next engineering detail

Storage monitoring, trip costs and crop-to-shipment losses are available as planning tools. Physical inventory scanning, refrigeration and vehicle systems require their own connections.

08 / FILMS / BAGS / LINERS / PACKAGING

Make the material fit the job

Consider the greenhouse covering, crop container, retail pack and transport protection as distinct material requirements.

  1. Define dimensions, thickness, exposure and product-contact requirements.
  2. Compare the relevant film, bag, liner or formed-pack process.
  3. Confirm supply, compatibility, quantity and handling before a quote.
Assembly scope and next engineering detail

American Plastic links products and manufacturing pathways across industries. A supplier process or reference product is not relabeled as an original machine design.

09 / FARM LOADS / GENERATION / COMPUTE

Put available energy to work

Connect the farm’s essential power needs with suitable generation and separately defined computing workloads.

  1. Account for essential farm demand and dependable energy supply.
  2. Identify compatible fuel, generation, power quality and cooling.
  3. Evaluate the remaining capacity for GPU or ASIC workloads and useful heat.
Assembly scope and next engineering detail

The farm-energy pathway considers biodiesel alongside the farm’s essential power needs. Conversion equipment, qualified fuel and actual electrical capacity must be established; the scenario tools keep energy, costs and workload assumptions explicit.

02 / SUPPORTING PROJECTS

Each idea earns
its place.

Four supporting projects, each with a purpose, an assembly to inspect and a prototype milestone.

01 / DESIGN CONCEPT

Earlier guided-head workshop

Compare the earlier guided-head cart with the current rolling lift and interchangeable single-cup tool.

A small, inspectable assembly for testing one careful pick before scaling to a moving greenhouse cart.

Next prototype milestone

Build and test the supported pick: seal stability, stem separation, reachable fruit and immediate or delayed bruising.

02 / DESIGN CONCEPT

Sensor Scout

Bring air, light, moisture and leaf observations into one sensing station.

Start a greenhouse upgrade with measurements that can be compared over time and across growing zones.

Next prototype milestone

Match sensor interfaces and calibration, then compare a full week of readings against reference instruments.

03 / DESIGN CONCEPT

Vent & Shade Mover

Connect a small roof vent and shade screen with bounded, solar-assisted motion.

Upgrade one bay at a time, linking local conditions to a specific movement with travel limits and manual control.

Next prototype milestone

Bench-test both loads, rated drivers, travel limits, power demand and a deliberate manual stop.

04 / DESIGN CONCEPT

Crop Eye

Capture repeatable crop views alongside the conditions around the plant.

Give a grower comparable observations and a record of change before adding automated interpretation.

Next prototype milestone

Fix the camera position, define lighting and time stamps, and validate the images with an operator.

03 / HARDWARE MEETS SOFTWARE

Labs builds the concept.
Compute connects the software.

Explore the custom greenhouse explorer, crop and energy models, shared recipe demonstrations and request workflows at Forem Compute. Each module has a distinct job and a working route through the site.

Explore our software ↗

THE NEXT PRACTICAL STEP

Bring a problem
worth solving.

Start with your crop, working space, existing equipment and the task you want to improve. Turn that need into a bounded prototype brief.