DIY AI ROBOT KIT · ADVANCED
Earlier guided-head workshop
Earlier single-cup lift-and-slide study, retained for component comparison. The current Forem machine uses a larger rolling lift, supported approach slide and one interchangeable suction cup; inspect it at Compute + Labs.
The current Forem harvesting platform.
One rolling Y-platform, a vertical carriage and crop-specific tools. Inspect the current design here; the earlier component study remains in the archive below.
Forem Labs / ROLL · LIFT · APPROACH
One cup. One grape tomato.Forem Greenhouse Harvester · positioning model
Optional: gently part the canopy
Two soft guides beside the picking head could extend into the foliage, part leaves and retract. This is a motion illustration; force limits, snag response and plant damage need testing.
Move the picking head & inspect dimensions
WORKING ENVELOPE / METRES
Roll along the aisle.
Lift the whole tool carriage.
All dimensions are design assumptions for the greenhouse model. The controls move connected geometry; they do not operate equipment or establish load capacity.
Manual controls show roll, lift and approach. Use the picking cycle to follow the fruit into the catch basket and main case.
TOOL HEAD / CLOSE APPROACH
Move the picking head 20 mm at a time.
The approach motor turns the screw. Its moving nut slides the deck and the single suction cup toward the crop. The camera stays on the lift carriage. The echo sensor moves with the tip to check the remaining gap.
Open the close-up, then advance three times to see the tool head move toward the same fruit. The camera view holds steady so you can see the gap close.
Aisle travel is held while the carriage is raised or the tools extend. This is a preview interlock, not a validated machine safeguard.
- Overall running footprint
- 820 × 1,050 mm
- Fixed mast height
- 2,600 mm
- Current suction-cup height
- 1.49 m
- Modelled bed-edge aisle
- 2.10 m
- Lane centre toward near bed
- +200 mm
- Near wheel to bed edge
- 440 mm
- All stowed hardware to near bed
- Loading geometry
The full-hardware gap is smaller than the wheel gap. Both are model geometry only; foliage, crop movement, floor variation and safe operating clearance are unverified.
Earlier component study · archived reference
3D model loads when you scroll here
Authored real-time 3D using the greenhouse models, not supplier CAD or photographs.
Parts list (15)
- Arduino-compatible climate sensor nodeRead local climate sensors and report the zone condition to the greenhouse coordinator.
- Harvester onboard computerLog camera frames and command the development sequence through a separate motion controller.
- Harvest-tool fruit cameraObserve the fruit and pedicel near the tool before an operator-approved pick.
- Soft food-contact suction cupSupport one tomato during the validated separation and transfer sequence.
- Harvester vacuum pumpRemove air from the cup circuit to establish a measured holding vacuum.
- Vacuum-line filter & catch vesselKeep plant debris and entrained moisture out of the vacuum pump.
- Cup vacuum pressure sensorCheck that the cup has a stable seal before separation or transfer.
- Vacuum release valveVent the cup to release a supported fruit into the receiving tray.
- Short-reach picking slideMove the tool laterally from the aisle toward an accessible fruit.
- Harvester lift drive & brakeRaise the carriage and hold its load when movement stops.
- Compliant picking wristAllow the soft cup to meet a fruit surface without a rigid impact.
- Guarded pedicel cutting headSeparate the selected pedicel after the fruit is supported and the cut path is confirmed.
- Padded shallow receiving trayReceive the supported fruit with a short controlled transfer and low stacking depth.
- Harvester emergency-stop circuitStop powered motion through an independently selected local stop path.
- Lift cable & hose carrierGuide camera, motor and vacuum lines through the lift’s moving travel.
Assembly overview
- 01 · Position in the aisle: The cart stops at an accessible fruit. Braking, wheel feedback and a clear work envelope precede tool motion.
- 02 · See the fruit and stem: Use the local camera to check color, position and the visible pedicel. Occluded fruit is skipped; operator-assisted picking is the first development mode.
- 03 · Align a soft contact: The mast and short slide bring the compliant cup to the fruit without pushing a cluster into the plant.
- 04 · Confirm the vacuum seal: Apply the tested low-vacuum setting, measure the cup pressure and cancel on leakage or excess contact force.
- 05 · Separate the pedicel: In this earlier linear-lift iteration, a guarded head separates the visible stem while the cup supports the fruit. The current pepper revision instead specifies an electrically heated wire; this earlier blade sequence remains historical.
- 06 · Lower into a shallow tray: Retract clear of the vine, lower the supported fruit close to the padded tray and vent the cup for a gentle release.
- 07 · Inspect and record: Record row, fruit condition and handling outcome. Check immediate damage and delayed bruising before approving repeated use.
- 08 · Clean, reset, repeat: An operator clears the work area and inspects the cup, cutter and trap. A fault or emergency stop requires a deliberate local reset.
Proposed kit configuration for learning and supervised trials. Final compatibility, wiring, power and software are specified with the quote; no ready-to-run kit or firmware download is supplied here. Not a certified safety system or a field-proven machine; test on your own crop before relying on it.
Related products
Robotics electronics (harvest workshop) (5 shared parts) ↗Measure: sensing core + crop camera (1 shared part) ↗Sensor Scout kit (1 shared part) ↗Vent & Shade Mover kit (1 shared part) ↗Sensors & controllers (in the 3D greenhouse) (1 shared part) ↗Phone & compute parts (modelled) (1 shared part) ↗
All products & quote basket ↗Tomato sales ↗Greenhouse Living System ↗
One Forem network
From the greenhouse
to the buyer.
Choose products, plan a project or request a produce program. Each route explains how prices, availability and delivery are confirmed.
- 01 / See itInside the greenhouseExplore all 212 components in place and follow any part from storage to the crop.
- 02 / Choose itAll products & quote basketOne catalog for named products and greenhouse parts. Add items and request a single quote.
- 03 / Build itSetups, electronics & robot kitsThe complete greenhouse setup from starter to full build, plus DIY AI robot kits.
- 04 / Buy the cropFarm Fresh to MarketExplore the documented tomato, citrus, pepper, vegetable and fruit range. Request your pack and supply program.
- 05 / Build the farmFarm Infrastructure salesStructure, growing systems and installation scope for a complete farm setup. A separate sales business within Forem.
- 06 / Plan itGreenhouse Living SystemExplore the greenhouse, growing systems, shared intelligence and energy planning under Forem Farm Infrastructure.
