CATEGORY / DIY AI ROBOT KITS
Robots you build yourself.
Arduino-class controllers, actuators, sensors and a suction pick-and-place tool. Every kit lists its parts, how it goes together, and the greenhouse job it does.
Open interactive 3D ↗Beginner
Sensor Scout kit
A proposed sensing configuration for air temperature, humidity, light, leaf wetness and substrate moisture, with logging on a Wi-Fi Arduino-class board.
Parts & assembly overview
Parts list
Assembly overview
- Specify and test a compatible logging sketch and Wi-Fi configuration; firmware is a project requirement, not an included download.
- Select compatible sensor interfaces and cable, then check the readings on a bench.
- Mount the air probe shaded at canopy height and the light sensor level at the crop plane.
- Insert the substrate probe in a representative bed; place the leaf-wetness sensor in the canopy.
- Compare readings for a week before using them to drive anything.
Greenhouse jobs
Sensing core upgrade ↗Shared greenhouse recipe ↗
Proposed kit configuration for learning and supervised trials. Final compatibility, wiring, power and software are specified with the quote; no ready-to-run kit or firmware download is supplied here. Not a certified safety system or a field-proven machine; test on your own crop before relying on it.
Open interactive 3D ↗Intermediate
Vent & Shade Mover kit
A proposed solar-powered actuator configuration for a small roof vent and shade screen, with controller commands and independent travel limits.
Parts & assembly overview
Parts list
Assembly overview
- Specify compatible power, enclosure and control software, then bench-test the solar panel, charge controller and battery.
- Select rated motor-driver channels and fusing for both loads; set the actuator stroke for the compatible vent.
- Thread the pull cord over the pulleys and fit the screen drive and independent travel-limit switches.
- Test controller commands, limits and manual stop before enabling any temperature or light response.
- Install on one compatible vent and one bench screen, then observe the bounded trial through a full day.
Greenhouse jobs
Solar vent motion ↗Automatic shade ↗
Proposed kit configuration for learning and supervised trials. Final compatibility, wiring, power and software are specified with the quote; no ready-to-run kit or firmware download is supplied here. Not a certified safety system or a field-proven machine; test on your own crop before relying on it.
Open interactive 3D ↗Beginner
Crop Eye camera kit
A proposed fixed-camera configuration for time-aligned crop photos alongside sensor data. A compatible capture computer, power supply and software are additional project requirements.
Parts & assembly overview
Parts list
Assembly overview
- Specify a compatible capture computer, power supply and camera software separately, then test a capture schedule on the bench.
- Fix the mount so it frames the same plants every day.
- Place the color/scale calibration target in frame.
- Confirm the gateway interface and time synchronization before transferring images and sensor logs.
- Review weekly growth images next to the climate record.
Greenhouse jobs
Crop camera viewpoint ↗
Proposed kit configuration for learning and supervised trials. Final compatibility, wiring, power and software are specified with the quote; no ready-to-run kit or firmware download is supplied here. Not a certified safety system or a field-proven machine; test on your own crop before relying on it.
Open interactive 3D ↗Advanced
Earlier guided-head workshop
Earlier single-cup lift-and-slide study, retained for component comparison. The current Forem machine uses a larger rolling lift, supported approach slide and one interchangeable suction cup; inspect it at Compute + Labs.
Parts & assembly overview
Parts list
Assembly overview
- 01 · Position in the aisle: The cart stops at an accessible fruit. Braking, wheel feedback and a clear work envelope precede tool motion.
- 02 · See the fruit and stem: Use the local camera to check color, position and the visible pedicel. Occluded fruit is skipped; operator-assisted picking is the first development mode.
- 03 · Align a soft contact: The mast and short slide bring the compliant cup to the fruit without pushing a cluster into the plant.
- 04 · Confirm the vacuum seal: Apply the tested low-vacuum setting, measure the cup pressure and cancel on leakage or excess contact force.
- 05 · Separate the pedicel: In this earlier linear-lift iteration, a guarded head separates the visible stem while the cup supports the fruit. The current pepper revision instead specifies an electrically heated wire; this earlier blade sequence remains historical.
- 06 · Lower into a shallow tray: Retract clear of the vine, lower the supported fruit close to the padded tray and vent the cup for a gentle release.
- 07 · Inspect and record: Record row, fruit condition and handling outcome. Check immediate damage and delayed bruising before approving repeated use.
- 08 · Clean, reset, repeat: An operator clears the work area and inspects the cup, cutter and trap. A fault or emergency stop requires a deliberate local reset.
Greenhouse jobs
Current crop-specific machine ↗Harvest system guide ↗Tomato sales ↗
Proposed kit configuration for learning and supervised trials. Final compatibility, wiring, power and software are specified with the quote; no ready-to-run kit or firmware download is supplied here. Not a certified safety system or a field-proven machine; test on your own crop before relying on it.