GREENHOUSE SETUP · TIER 05
Full build: harvest workshop
Earlier linear-lift workshop reference: a narrow aisle cart, a guided lift and a short-reach suction-and-cutting head. Its assembly steps and budget remain available for comparison. The Forem Greenhouse Harvester shares one supported suction cup, one ordinary camera, proposed close-range acoustic sensing and a guarded heated-wire stem cutter across tomato and pepper modes. Optional soft leaf guides part the canopy; crop fit and all handling outcomes need trials. Development concept, not a field-proven machine.
The current Forem harvesting platform.
One rolling Y-platform, a vertical carriage and crop-specific tools. Inspect the current design here; the earlier component study remains in the archive below.
Forem Labs / ROLL · LIFT · APPROACH
One cup. One grape tomato.Forem Greenhouse Harvester · positioning model
Optional: gently part the canopy
Two soft guides beside the picking head could extend into the foliage, part leaves and retract. This is a motion illustration; force limits, snag response and plant damage need testing.
Move the picking head & inspect dimensions
WORKING ENVELOPE / METRES
Roll along the aisle.
Lift the whole tool carriage.
All dimensions are design assumptions for the greenhouse model. The controls move connected geometry; they do not operate equipment or establish load capacity.
Manual controls show roll, lift and approach. Use the picking cycle to follow the fruit into the catch basket and main case.
TOOL HEAD / CLOSE APPROACH
Move the picking head 20 mm at a time.
The approach motor turns the screw. Its moving nut slides the deck and the single suction cup toward the crop. The camera stays on the lift carriage. The echo sensor moves with the tip to check the remaining gap.
Open the close-up, then advance three times to see the tool head move toward the same fruit. The camera view holds steady so you can see the gap close.
Aisle travel is held while the carriage is raised or the tools extend. This is a preview interlock, not a validated machine safeguard.
- Overall running footprint
- 820 × 1,050 mm
- Fixed mast height
- 2,600 mm
- Current suction-cup height
- 1.49 m
- Modelled bed-edge aisle
- 2.10 m
- Lane centre toward near bed
- +200 mm
- Near wheel to bed edge
- 440 mm
- All stowed hardware to near bed
- Loading geometry
The full-hardware gap is smaller than the wheel gap. Both are model geometry only; foliage, crop movement, floor variation and safe operating clearance are unverified.
Earlier component study · archived reference
3D model loads when you scroll here
Authored real-time 3D using the greenhouse models, not supplier CAD or photographs.
Parts list (24)
- Ventilated Stack and Nest Container — BlueReceive and transfer gently picked tomatoes in a clean, shallow container while preserving lot identity and avoiding compression.
- Four Growers robotic harvestingTrial robotic picking of greenhouse tomatoes after validating the actual crop, support system and aisle arrangement.
- Greenhouse harvest cartCarry clean shallow harvest bins through the designated growing aisle.
- Shallow harvest containerHold gently picked tomatoes without stacking the crop too deeply.
- Crop-care pruning shearsMake the crop-care cuts specified by the growing team with a controlled clean tool.
- Crop-care waste containerKeep removed crop material separate from the accepted harvest.
- Harvest lot tagCarry row, harvest date and source-lot identity with a harvest container.
- Crop-scouting sticky cardSupport the grower’s insect-monitoring program at the selected crop-scouting position.
- Vented tomato shipping cartonCarry released produce from the clean harvest/packing workflow to dispatch.
- Tomato carton lidClose the matching shipping carton without blocking its intended ventilation.
- Carton insert & dividerSeparate selected retail packs or restrain movement inside a shipping carton.
- Shipping carton traceability labelCarry grower, lot, pack date and destination identity on each released carton.
- Crop-handling work glovesSupport the farm’s defined crop-care and handling hygiene procedure.
- Vented retail produce packHold a selected sale unit of tomatoes inside a compatible shipping carton.
- Harvest packing check scaleCheck a sampled filled pack against its selected net-weight target.
- Dispatch palletSupport a planned stack of released produce cartons for handling and dispatch.
- Pallet restraint stretch filmRestrain a compatible carton load during handling.
- In-house rolling harvester chassisCarry the harvest tool, control enclosure and receiving tray down one clear crop aisle.
- Harvester wheel & caster assemblySupport low-speed movement on the prepared service surface.
- Harvester wheel gearmotorTurn a driven wheel under current-limited low-speed control.
- Wheel position encoderMeasure driven-wheel rotation for speed and position feedback.
- Harvester dual motor driverControl the two wheel motors with independent direction and current limits.
- Harvester low-mounted batteryStore energy near the chassis floor to reduce the center of gravity.
- Harvester fuse & isolation switchProtect the selected battery circuit and provide service isolation.
Related products
VineFresh tomato packaging (7 shared parts) ↗Dispatch pallet & stretch film (4 shared parts) ↗Robotics electronics (harvest workshop) (2 shared parts) ↗Plastics: bags, films & retail packs (2 shared parts) ↗Phone & compute parts (modelled) (1 shared part) ↗
All products & quote basket ↗Tomato sales ↗Greenhouse Living System ↗
One Forem network
From the greenhouse
to the buyer.
Choose products, plan a project or request a produce program. Each route explains how prices, availability and delivery are confirmed.
- 01 / See itInside the greenhouseExplore all 212 components in place and follow any part from storage to the crop.
- 02 / Choose itAll products & quote basketOne catalog for named products and greenhouse parts. Add items and request a single quote.
- 03 / Build itSetups, electronics & robot kitsThe complete greenhouse setup from starter to full build, plus DIY AI robot kits.
- 04 / Buy the cropFarm Fresh to MarketExplore the documented tomato, citrus, pepper, vegetable and fruit range. Request your pack and supply program.
- 05 / Build the farmFarm Infrastructure salesStructure, growing systems and installation scope for a complete farm setup. A separate sales business within Forem.
- 06 / Plan itGreenhouse Living SystemExplore the greenhouse, growing systems, shared intelligence and energy planning under Forem Farm Infrastructure.
