Skip to contentFarm Fresh
to Market
Discuss a farm project
Menu

Forem Labs / Equipment design

Forem Greenhouse
Harvester

Designed by Michael Forem for Forem Labs. Follow one fruit from the plant to the main basket. The proposed machine combines an RGB camera, Michael Forem’s software and an Arduino controller to locate the fruit and guide the tool.

Development concept · harvest cycle simulation

Forem Labs / ROLL · LIFT · APPROACH

One cup. One grape tomato.
ONE SHARED PICKING HEAD
LOADING INTERACTIVE 3D

Forem Greenhouse Harvester · positioning model

Optional: gently part the canopy

Two soft guides beside the picking head could extend into the foliage, part leaves and retract. This is a motion illustration; force limits, snag response and plant damage need testing.

Move the picking head & inspect dimensions

WORKING ENVELOPE / METRES

Roll along the aisle.
Lift the whole tool carriage.

All dimensions are design assumptions for the greenhouse model. The controls move connected geometry; they do not operate equipment or establish load capacity.

Manual controls show roll, lift and approach. Use the picking cycle to follow the fruit into the catch basket and main case.

Grid spacing: 250 mm

TOOL HEAD / CLOSE APPROACH

Move the picking head 20 mm at a time.

The approach motor turns the screw. Its moving nut slides the deck and the single suction cup toward the crop. The camera stays on the lift carriage. The echo sensor moves with the tip to check the remaining gap.

Open the close-up, then advance three times to see the tool head move toward the same fruit. The camera view holds steady so you can see the gap close.

Aisle travel is held while the carriage is raised or the tools extend. This is a preview interlock, not a validated machine safeguard.

Overall running footprint
820 × 1,050 mm
Fixed mast height
2,600 mm
Current suction-cup height
1.49 m
Modelled bed-edge aisle
2.10 m
Lane centre toward near bed
+200 mm
Near wheel to bed edge
440 mm
All stowed hardware to near bed
Loading geometry

The full-hardware gap is smaller than the wheel gap. Both are model geometry only; foliage, crop movement, floor variation and safe operating clearance are unverified.

What these dimensions mean

The existing model places 900 mm beds at centres −1.50 m and +1.50 m, leaving a 2.10 m bed-edge aisle. The nearest planted line is at +1.20 m. The drawn paving is wider than that clear aisle and is not used as the clearance measurement. The pepper assembly adds a supported 90 mm adapter so its wire reaches that line at full approach; actual stems, foliage and obstacles need a survey.

The carriage value is its mounting datum. Tool heights are calculated separately from the mounted geometry. The base is deliberately held during lifting and crop approach; stability, payload, braking, floor slope remain engineering work. The picking cycle illustrates the proposed basket transfer and release.

  • Mast section and base ballast/load capacity
  • Guide rail series, bearing trucks and screw pitch/diameter
  • Lift actuator torque/speed, brake holding capacity and stop architecture
  • Approach actuator and stiffness
  • Cable-carrier bend radius and ratings
  • Crop payload, dynamic stability and allowable floor slope

THE PICKING CONCEPT

Approach. Hold. Transfer.

One compliant suction cup supports one tomato. The camera locates the visible fruit and stem, and the proposed acoustic sensor helps with the final approach. The guarded wire separates the supported fruit in the illustrated cycle. Cup fit, hold confirmation and cut quality need crop trials.

What this view establishes

The mast, carriage, guides and tool mounts define a connected mechanical envelope. Dimensions here are authored assumptions. Selected component drawings, load analysis and physical trials must establish compatibility and performance.

Every component & its purpose
  1. 01

    Locate and approach one fruit

    One regular RGB camera is intended to identify a reachable ripe grape tomato. The fixed crop illustration includes neighboring green fruit. The lift and approach slide position the single-cup carrier; a proposed tip echo sensor assists the last part of the approach.

  2. 02

    Hold, then separate the stem

    One soft cup supports the selected fruit. The latest shared head adds a guarded heated-wire span at the stem. Contact, cut quality and damage limits require crop trials.

  3. 03

    Catch, retract and empty the load

    The cup releases the picked fruit into the small padded basket while neighboring fruit stays on the vine. The example load reaches its full point, then the proposed guide and gate carry and empty the catch basket into the fixed main case.

The earlier static render is superseded by this dimensioned lift study. Selected supplier dimensions must replace assumed component envelopes before fabrication. No payload, stability, picking rate or labor saving has been established.

01 / CAMERA

See one fruit.

An ordinary RGB camera supplies the image. Camera calibration and a clear view of the stem matter at picking distance.

02 / SOFTWARE

Review the target.

See the crop records, image review and other working tools from Forem Compute. Connected picking control still needs equipment integration and trials.

Explore the software ↗
03 / ARDUINO

Limit the movement.

The proposed controller would handle local travel limits and stop requests. The model shows how roll, lift and approach position the tool before the basket transfer.

01 / CORE PART

Roll. Raise. Lower.

One Y platform travels along the row. The lift brings the compact head to the fruit.

02 / CORE PART

One camera.

An ordinary camera locates visible fruit and its stem.

03 / CORE PART

One close-range sensor.

An acoustic sensor beside the cup is intended to help with the final approach.

04 / CORE PART

One suction cup.

Hold one fruit with a soft cup selected for its size and surface.

05 / CORE PART

One heated wire.

Separate the supported fruit, switch off the heat and withdraw the head.

06 / CORE PART

One moving catch basket.

A padded basket receives the fruit below the cup. When full, it retracts and tips into the main case.

Optional soft leaf guides can extend beside the tip and retract after approach. These are canopy guides, not additional picking arms. Slow, force-limited movement and a stop on resistance are proposed; plant-safe contact still needs testing.

Inside the design · parts, controls and build budget

Design revision · 2026-11-03 · Moving catch basket

One rolling Y platform moves along the row and raises or lowers a compact picking head. The shared head uses one ordinary camera, one proposed close-range acoustic sensor, one suction cup and one guarded heated-wire stem cutter. A moving catch basket carries the picked fruit to the fixed main case. The greenhouse computer links to the local controller, and the same head accepts a cup sized for the crop.

LOCATE / HOUSE-LINKED CONTROL

See the target. Check the approach.

One ordinary camera identifies visible fruit and stem. One nearby acoustic sensor is a candidate for close-range approach assistance. Camera calibration, known geometry and vacuum feedback remain separate checks: a distance reading does not prove alignment or a seal. No infrared camera, LiDAR or radar is part of this baseline.

SUPPORT / CUT / WITHDRAW

One shared head. A crop-specific fit.

One compliant suction cup supports one tomato. The camera locates the visible fruit and stem, and the proposed acoustic sensor helps with the final approach. The guarded wire separates the supported fruit in the illustrated cycle. Cup fit, hold confirmation and cut quality need crop trials.

Insulated wire mounts, guarding, heat feedback and an independent cutoff require engineering and trials.

CATCH / FILL / EMPTY

Fill the basket. Empty it into the case.

The padded catch basket sits below the suction cup and collects the fruit as it is picked. Once the basket is full, it retracts and tips its load into the case. The guide and hinge are proposed. Fill sensing, clearance, stability and cushioning still need prototype tests.

OPTIONAL CANOPY ATTACHMENT

Part the leaves gently.

Optional soft canopy guides beside the picking tip extend and retract slowly to part leaves. They are leaf guides, not extra suction arms or the structural Y branches. The proposed control limits force and stops on resistance; guide material, contact force, reach and leaf or stem damage require physical tests. Gentle, damage-free operation is a design aim, not a verified result.

INDIVIDUAL FRUIT

Grape tomato · one at a time

Current illustrated head: one compliant cup and tip echo sensing. The drawn cup diameter is an assumption; confirm its fit and seal on the intended variety.

ALTERNATIVE CUP / SELECTION REQUIRED

Larger tomato or pepper support

Alternative interchangeable cup format. Diameter, connector, load and contact response remain unselected. For a pepper, the cup would support the fruit while the separate heated-wire tool cuts; it does not imply pulling the pepper free.

SAME MACHINE / DISTINCT MODE

Handle a whole truss.

Whole-truss handling is a distinct mode of the same Forem Greenhouse Harvester, separate from individual-fruit picking. Its support attachment, load distribution and stem-cutting arrangement still need definition and trials. The individual-fruit cup is not a demonstrated whole-cluster support.

The shared machine uses one rolling Y platform with vertical travel, one camera, one close-range acoustic sensor, one suction cup and one guarded heated-wire stem cutter. The owner’s intended infection-reduction benefit remains unproven: cutting temperature, power, dwell, wire material, insulation, guarding, crop damage and sanitation require testing. Acoustic range does not by itself prove alignment or a suction seal. All illustrated dimensions remain editorial assumptions, not approved fabrication specifications. Optional retractable soft leaf guides and whole-truss support remain development attachments.

THE LAST PART OF THE APPROACH

See the fruit.
Listen for the distance.

The regular camera identifies the target. One proposed transmitter/receiver module beside the single cup adds local echo-ranging before contact. A compliant cup and seal feedback provide separate contact checks.
ONE CUP / ONE SENSING PAIR

A short, supported tool.
A sensor at the tip.

The current interactive model above shows the cup, its removable fitting, the adjacent candidate transmitter and receiver, and one vacuum route. Select “One tip echo-sensing module” to inspect the mounting close up.

Inspect the current tool ↑The sensor package and cup interface are illustrative. Their selected dimensions, usable range and contact response remain to be measured.
SINGLE HEAD / LOCAL FEEDBACK

A measured approach.

  1. Observe. Select reachable fruit in the camera image.
  2. Ping, then listen. Emit a pulse from the tip module and measure its returning echo. Use the calibrated travel time to estimate distance.
  3. Slow and make compliant contact. Respect the sensor’s usable range. A soft mount and measured contact response govern the final travel.
  4. Confirm the seal. Check the single vacuum channel before attempting separation. Detachment and a reachable release path need separate mechanical trials.

A single range reading does not reveal surface angle, ripeness or a damage-free seal. Leaves, tilted fruit, water and reflections from the cup can confuse echoes. An uncertain reading means stop and recheck.

01 / TEST THE TIP

A low-cost ranging experiment.

A $5.25 HC-SR04 board is a bench reference, checked 24 October 2026. It uses ultrasonic ranging and advertises a 2 cm–4 m range. Its full-size board is not the selected tip sensor; the completed tip still needs suitable transducers, mounting and electronics.

02 / PROVE THE CONTACT

One fruit at a time.

Test a single cup on the intended crop variety: echo reliability, leaf interference, approach travel, seal, detachment and delayed bruising. Establish workable geometry and control limits for this single head.

03 / CHANGE THE CUP

Fit the fruit. Keep the base.

A larger-fruit cup is an interchangeable option, with its diameter, seal and load limit still to be selected. Recheck the echo path after any cup change. Both crop views use one supporting cup and a guarded heated wire on the shared head. The main padded basket receives the fruit after the head withdraws; transfer still needs development.

Frequency, sensor limits & engineering references

The transmitter emits sound; the receiver detects its return. A 40 kHz ultrasonic reference is a practical bench starting point. The suggested 12–15 Hz is infrasound and is not the selected frequency for this small-target ranging study. Final frequency, beam and minimum usable distance must follow the chosen transducer and tests.

For a transmitter and receiver at effectively the same location, the basic estimate is distance = sound speed × elapsed time ÷ 2. Separated tip transducers measure the sum of two travel paths; installed geometry needs its own calibration. Temperature and transducer ring-down also affect the estimate. A setback behind the cup lip is a candidate arrangement to investigate, not proof that the blind zone is solved.

Adafruit: 40 kHz ranging and interface ↗Texas Instruments: ultrasonic signal-processing reference ↗

This is an integration concept, not a selected production sensor, validated collision system or claim of patentability.

CONNECTED GROWING / Forem Labs

One machine.
Part of the whole house.

The fruit-level sensor belongs to the harvester. The climate sensors belong to the growing house. The computer brings both records together, so a harvest observation stays connected to the conditions in which that fruit grew.

Interactive system plan · example readings
01 / THE GROWING HOUSE

House A

Air temperature
27°C
Relative humidity
65%
Light at the crop
900 μmol/m²/s

Light, humidity and temperature stay attached to this house and its crop stage. Shade, mist, vents and fans respond locally.

Compare the houses ↗
02 / HARVESTER CONTROL

Lift. Approach. Sense.

  • One cup and a nearby echo-sensing tip
  • Vacuum feedback confirms the hold
  • Lift and approach positions identify the reach
  • House and machine IDs identify the work

The controller checks its own limits. A lost echo, unconfirmed hold or stop request cannot be overridden by the computer.

03 / Forem Compute

Connect the observations.

The intended neural layer combines crop images, growing conditions and harvest outcomes. Its recommendations return to the correct house and machine, with their local limits retained.

Equipment connection: awaiting commissioning
Trained model connection: not present in this build

Share a successful growing recipe with houses at the same crop stage. Keep each house’s own readings and control response. The current comparison tool performs this target sharing; the neural and equipment interfaces are defined for integration.

ONE CUP + TIP SENSING + HEATED WIRE / THE BUILD PLAN

Buy the right parts.
Build the rest in-house.

One shared head supports the selected tomato with one cup and positions a guarded heated wire at the stem. The rolling lift, one ordinary camera and one proposed acoustic tip module serve both crop views. Optional soft leaf guides have their own quotation lines; omit them explicitly if not needed.

Proposed workshop budget · not a final machine price
Entered parts$767.20$170.20 uses unchanged dated supplier references.
Entered in-house work$2,556.00142 entered hours · 8 missing labor inputs.
Known scope + contingency$3,821.6831 component lines remain unpriced. This is an incomplete planning envelope.

Each crop view budgets one configuration of the same machine. Shared chassis, lift and controls appear in both views; do not add the two totals together as an all-tools price. Blank means unknown; an entered zero means an explicit zero-cost assumption. Unpriced components stay outside the subtotal. The example hours, hourly cost and material allowances are editable assumptions, not observed Forem spending or a promise that the machine can be completed in that time.

Purchased parts and in-house materials 48 lines
Component and scopeQty.Your unit budget / USDEntered line / USD
Rolling baseChassis tube, plates and fastenersPlanning allowance

In-house frame material only. Replace with the actual cut list; fabrication labor is entered separately.

1material allowance$120.00
Rolling baseWheel, caster and hub assembliesPlanning allowance

Provisional Y layout: two front wheels and one rear follower. Drive, steering, brakes, loading, cleaning and hub fit still require selection.

3wheel assembly$54.00
Rolling base37D traction motor with encoderDated supplier reference · 2026-10-17

Dated light-cart candidate. Encoders are included here and are not charged again. Light development-cart reference. Continuous gearbox limit and motor heating, wheel load and aisle grade govern selection; the stall torque is not a continuous rating. Backorders allowed

Pololu · original reference $60.95 ↗
2motor including encoder$121.90
Rolling baseArduino-compatible traction driverQuote required

Select a matched two-channel drive interface, current limit and stop path.

1rated driver assemblyUnpriced
Vertical positioningFabricated mast and chassis reinforcementQuote required

Drawn dimensions are layout assumptions. Quote sections, base attachments and ballast only after payload and stability analysis.

1structural assemblyUnpriced
Vertical positioningMatched vertical rails and bearing trucksQuote required

Select series, lengths, truck spacing and mounting tolerances from measured forces and moments.

1paired guide setUnpriced
Vertical positioningCarriage plate, nut mount and guide interfacesQuote required

Cost machining, fasteners and mounting faces from reviewed drawings; fabrication hours are separate.

1fabricated assemblyUnpriced
Vertical positioningLift screw, nut, bearings, motor and driverQuote required

Illustrative lead-screw architecture only. Quote after travel, speed, payload, buckling and critical-speed checks.

1matched drive setUnpriced
Vertical positioningRated lift holding brake or fall arrestQuote required

Specify independent power-loss and fault behavior; do not assume a motor can safely hold the raised payload.

1holding systemUnpriced
Vertical positioningUpper/lower limits and physical end stopsQuote required

Select switches, stop structure, wiring and stopping-distance allowance for the actual lift drive.

1travel protection setUnpriced
Vertical positioningVertical energy chain and rated moving servicesQuote required

Quote carrier radius, travel, anchors, cables, hoses and protection against moisture and repeated bending.

1carrier and cable/hose setUnpriced
Crop approachSupported approach rails, trucks and mounting deckQuote required

The drawn stroke and deck are assumptions. Quote for stiffness, tool loads and near-row clearance.

1slide assemblyUnpriced
Crop approachApproach screw, nut, drive and end limitsQuote required

Select against tool reach and force. Include stops and return-position feedback; no speed or torque is assumed.

1matched drive setUnpriced
Seeing and controlArduino motion controllerQuote required

Choose the actual Arduino board, I/O and communications interface. No approved exact board price has been supplied.

1controllerUnpriced
Seeing and controlOne shared RGB cameraDated supplier reference · 2026-10-17

One regular visible-light camera serves the machine. No infrared, LiDAR or radar unit is included. Calibrate its view and re-observe between movements. 12MP RGB camera module only. Computer, correct ribbon cable, housing, calibration and crop-analysis software are additional; it does not measure crop PPFD. Listed price; confirm fulfillment

Adafruit · original reference $29.25 ↗
1camera module$29.25
Seeing and controlLocal computer — capture-board candidateDated supplier reference · 2026-10-17

A low-cost capture-board reference; benchmark the final camera and software before choosing the production computer. Low-cost capture/control computer example. Power, memory, headers and camera adapter cable are separate; throughput for a trained vision model is not established. Out of stock

Adafruit · original reference $19.05 ↗
1bare board, without header$19.05
Seeing and controlComputer storage, power and camera adapterPlanning allowance

Match storage, camera cable, power and cooling to the final computer.

1accessory allowance$35.00
Single-cup toolIn-house supported single-cup carrier and braceQuote required

One fixed carrier on the accepted lift/approach deck. Quote material, bracket, fasteners and stiffness review; no articulated hand or finger actuators are assumed.

1fabricated carrierUnpriced
Tip echo sensingOne miniature tip transmitter/receiver ranging moduleQuote required

Quote suitable transducers and electronics. Verify minimum range, size, cup blockage, crop echoes and mist exposure; a full-size hobby board is not a selected tip.

1tip moduleUnpriced
Tip echo sensingSingle-channel echo acquisition and interfaceQuote required

Include signal conditioning, timing and calibration for one tip. No multi-finger scheduling or eight-channel controller is needed.

1control assemblyUnpriced
Tip echo sensingTip sensor mount, wiring and protectionQuote required

Keep the sensing faces clear while fitting the cup. Geometry is an integration study, not proof that the installed blind zone is solved.

1integration setUnpriced
Single vacuum channelOne soft suction cup and food-contact fittingPlanning allowance

Illustrative allowance for one cup. Select diameter and material for grape tomatoes; test the seal, holding response and delayed marking.

1cup allowance$30.00
Interchangeable cup optionsRemovable cup fitting and alternate-head interfaceQuote required

Choose a sealed compatible interface. Larger tomatoes or pepper support require a separately selected cup diameter and load test; no universal fitting or one-size cup is assumed.

1interface setUnpriced
Single vacuum channelSingle vacuum hold and release valvePlanning allowance

One valve controls the single head. Confirm flow, leakage, response and pressure rating.

1valve allowance$25.00
Single vacuum channelSingle cup-pressure feedback sensorPlanning allowance

One measured seal channel. Pressure feedback does not locate fruit or replace the camera and tip echo study.

1sensor allowance$35.00
Single vacuum channelVacuum source for one cupQuote required

Select after measuring holding force, leakage and duty. Simplifying to one head reduces component count but does not establish a completed machine price.

1pump packageUnpriced
Single vacuum channelFilter and cleanable catch vesselPlanning allowance

Allow for moisture and debris capture, service access and pressure drop.

1filter/trap allowance$25.00
Single vacuum channelOne vacuum hose route and fittingsPlanning allowance

One route follows the carriage and supported tool. Replace with actual length, bore and moving-bend requirements.

1hose/fitting allowance$18.00
Shared heated-wire headReplaceable electrically heated cutting wireQuote required

Select wire material and replaceable terminals against controlled stem-cutting trials. No gauge, temperature, power or dwell is specified.

1wire and terminal setUnpriced
Shared heated-wire headElectrically insulating mounts and tension adjustmentQuote required

Support the cutting span with electrical and thermal isolation. Quote insulation, terminals and adjustable retention after selecting the wire and testing expansion.

1mounting setUnpriced
Shared heated-wire headIn-house wire carrier, guard and withdrawal fixtureQuote required

Fabricate a compact guarded wire holder on the same carrier as the single cup. Determine hot-tool clearance and withdrawal in trials.

1fabricated assemblyUnpriced
Shared heated-wire headBounded wire approach and withdrawal mechanismQuote required

Quote any local wire adjustment needed beyond the shared lift and approach slide. No separate articulated cutter arm is assumed.

1motion and feedback setUnpriced
Shared thermal systemDedicated current-limited heating supply and driverQuote required

Size the wire supply, rated switching, current limit and protection after measurement. Do not infer heater power from the motion-controller price.

1power branchUnpriced
Shared thermal systemHeat-control electronics and independent cutoffQuote required

Define enable, stop, fault and wire-break behavior; include independent removal of heating power. Develop and validate this separately from normal motion software.

1control and protection setUnpriced
Shared thermal systemWire-temperature measurement and calibrationQuote required

Select a suitable feedback method and mounting; compare transients and cut conditions against a reference before choosing settings.

1sensing setUnpriced
Shared thermal systemProtected heater leads, terminals and disconnectQuote required

Quote wire-compatible connectors, insulation, strain relief and protected movement routing. Keep heater circuitry distinct from camera and low-power sensing cables.

1electrical routing setUnpriced
Optional canopy accessOptional soft retractable leaf-guide pairQuote required

Optional attachment, not two additional picking arms. Quote compliant guides, mounts and cleanable contact materials. Enter zero only if omitted from your scope.

1attachment setUnpriced
Optional canopy accessOptional bounded guide drive and force feedbackQuote required

Quote limited extension, resistance sensing, stop and retract behavior after plant trials. Enter zero only if this attachment is omitted.

1drive and feedback setUnpriced
Power and safeguardsProtected battery and matched chargerQuote required

Size peak current, duty and runtime after load tests. No assumed battery capacity or runtime is sold here.

1power packageUnpriced
Power and safeguardsFusing, disconnect, converters and wiringPlanning allowance

Match every voltage, connector and load. The battery/charger and motor drivers are separate lines.

1electrical allowance$55.00
Power and safeguardsIndependent local stop and reset hardwarePlanning allowance

Provisional allowance. Select the stopping architecture against the actual machine and working area.

1stop-system allowance$80.00
Power and safeguardsContact bumper and mountingPlanning allowance

Contact feedback for supervised positioning.

1bumper allowance$50.00
Power and safeguardsCable and hose carrier, strain reliefPlanning allowance

Replace with actual travel, bend radius and length.

1routing allowance$25.00
Handling and setupMain receiving bin and cleanable paddingPlanning allowance

Receive fruit from the small catch basket. Confirm capacity, cleaning and handling damage.

1bin allowance$25.00
Basket transferMoving catch basket and cleanable linerQuote required

Quote a small padded receiver that fits the selected fruit. Check food-contact materials, cleaning and bruising.

1basket assemblyUnpriced
Basket transferProposed basket guide, mounts and driveQuote required

Quote the supported return after reviewing full-basket payload, aisle clearance, fill detection and stop behavior.

1transfer assemblyUnpriced
Basket transferProposed discharge hinge and tilt controlQuote required

Quote the hinge, drive and position feedback after checking how the fruit lands in the main basket.

1discharge assemblyUnpriced
Handling and setupRGB camera mount and calibration fixturePlanning allowance

One camera mount and reference target, without a separate depth sensor.

1fixture allowance$20.00

FABRICATE / INTEGRATE / PROVE

Count our work, too.

Editable starter allowances for in-house work. Review every hour against this crop’s mechanism, single-cup alignment, heated-wire cutting and transfer, and the first supervised trial.

Scope our first prototype ↗

Saved separately for this crop on this browser. Earlier machine budgets are kept separate. Supplier reference dates are preserved and require reconfirmation.